reused junk

メニュー

2009-01-16T19:22:07+09:00

**メニュー ■[[WLI-PCM-L11]] ■[[BLR-TX4]] ├ [[シリアル接続>BLR-TX4@SCI]] ├ [[JTAG>BLR-TX4@JTAG]] └ [[GCC>BLR-TX4@GCC]] ■[[WLAR-L11]] └ [[シリアル接続>WLAR-L11@SCI]] ■[[WLA-G54]] ├ [[DD-WRT化>WLA-G54@toDD-WRT]] ├ [[openvpn失敗>WLA-G54@failOPENVPN]] └ [[JTAG探し>WLA-G54@findJTAG]] ■[[BLR3-TX4]] ├ [[シリアル接続>BLR3-TX4@SCI]] ├ [[WHR-G54化>BLR3-TX4@toWHR-G54]] ├ [[DD-WRT失敗>BLR3-TX4@failDD-WRT]] ├ [[復旧>BLR3-tx4@repair]] └ [[カーネル乗せ換え>BLR3-tx4@onLinux]] ■[[PCVA-141LAP]] ---- // リンクを張るには "[" 2つで文字列を括ります。 // ">" の左側に文字、右側にURLを記述するとリンクになります //**更新履歴 #recent(10,ignore=メニュー) |TOTAL|:|&counter(total)| |TODAY|:|&counter(today)| |YESTERDAY|:|&counter(yesterday)|

BLR3-TX4@onLinux

2009-01-16T19:19:27+09:00

*カーネルを2.6.26.8に乗せ換えた &spanclass(fillbox){動いた} 2.6.26.8のカーネルにdebian(sarge)を積んで動いた。カーネル自体はkurobox(無印)向けのパッチを当てた上で、修正、追加することで動作した。変更箇所を簡単に示すと・タイマ割込みに外部WDTのクリアを追加・MTDのFlashROMのアドレスを変更・LAN側のAN983Bの内蔵PHYをdisableし外付PHY(BCM5325)を使うよう修正 ---- &spanclass(fillbox){dmesg} KURO-BOX:~# dmesg KERNELBASE=c0000000 (r6=9030c0 r7=9030c0) r3=ff000001 (r4=904000 r5=e63260) Linux version 2.6.26.8-kurobox (HO@busters) (gcc version 3.3.5) #24 Thu Jan 15 13:39:36 JST 2009 Early serial console at MMIO 0x80004600 (options '57600n8') console [uart0] enabled BUFFALO Network Attached Storage Series (C) 2002-2005 BUFFALO INC. Entering add_active_range(0, 0, 16384) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 16384 Normal 16384 -> 16384 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 16384 On node 0 totalpages: 16384 DMA zone: 128 pages used for memmap DMA zone: 0 pages reserved DMA zone: 16256 pages, LIFO batch:3 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,57600 OpenPIC Version 1.2 (1 CPUs and 11 IRQ sources) at 80040000 PID hash table entries: 256 (order: 8, 1024 bytes) decrementer frequency = 24.391680 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 56476k available (1968k kernel code, 832k data, 124k init, 0k highmem) Calibrating delay loop... 129.53 BogoMIPS (lpj=259072) Mount-cache hash table entries: 512 net_namespace: 480 bytes NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Cannot allocate resource region 1 of device 0000:00:00.0 Registering openpic with sysfs... NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 5500k freed JFFS2 version 2.2. (NAND) ﾂｩ 2001-2006 Red Hat, Inc. msgmni has been set to 121 io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x80004600 (irq = 26) is a 16550A console handover: boot [uart0] -> real [ttyS0] serial8250.1: ttyS1 at MMIO 0x80004500 (irq = 25) is a 16550A brd: module loaded loop: module loaded Linux Tulip driver version 1.1.15 (Feb 27, 2007) tulip0: MII transceiver #1 config 3000 status 7829 advertising 05e1. tulip0: MII transceiver #2 config 3000 status 7809 advertising 05e1. tulip0: MII transceiver #3 config 3000 status 7809 advertising 05e1. tulip0: MII transceiver #4 config 3000 status 7809 advertising 05e1. eth0: ADMtek Comet rev 17 at Port 0xbfff00, 00:07:40:85:46:4a, IRQ 16. tulip1: MII transceiver #1 config 1000 status 7849 advertising 05e1. eth1: ADMtek Comet rev 17 at Port 0xbffe00, 00:07:40:85:46:4b, IRQ 17. physmap platform flash device: 00800000 at ff800000 physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 physmap-flash.0: Swapping erase regions for broken CFI table. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available Using physmap partition information Creating 5 MTD partitions on "physmap-flash.0": 0x00000000-0x00700000 : "mtd_firmimg" 0x00700000-0x00770000 : "mtd_bootcode" 0x00770000-0x00780000 : "mtd_status" 0x00780000-0x00800000 : "mtd_conf" 0x00000000-0x00800000 : "mtd_allflash" mice: PS/2 mouse device common for all mice TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 124k init ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x04, vendor 0x4243) ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x05, vendor 0x4243) ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x02, vendor 0x4243) ssb: Core 3 found: V90 (cc 0x807, rev 0x02, vendor 0x4243) ssb: Core 4 found: PCI (cc 0x804, rev 0x09, vendor 0x4243) ssb: SPROM revision 1 detected. ssb: Sonics Silicon Backplane found on PCI device 0000:00:0e.0 b43-phy0: Broadcom 4306 WLAN found phy0: Selected rate control algorithm 'pid' Broadcom 43xx driver loaded [ Features: PNR, Firmware-ID: FW13 ] input: b43-phy0 as /class/input/input0 firmware: requesting b43/ucode5.fw firmware: requesting b43/pcm5.fw firmware: requesting b43/b0g0initvals5.fw firmware: requesting b43/b0g0bsinitvals5.fw b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10) b43-phy0: Radio turned on by software eth0: Setting full-duplex based on MII#1 link partner capability of 41e1. ip_tables: (C) 2000-2006 Netfilter Core Team input: b43-phy0 as /class/input/input1 b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10) KURO-BOX:~# ---- &spanclass(fillbox){} ----

BLR3-tx4@repair

2008-08-19T12:43:24+09:00

*復旧 &spanclass(fillbox){調査} どうも入れたDD-WRTのファームとWHR-G54のファームでは構造がぜんぜん違うようだ。「ALERT MODE」についての情報があった。 &html(http://www.yamasita.jp/BBS/618.html) ---- &spanclass(fillbox){作業} コマンドで md を実行するが途中で表示が止まる。どうも ledstop を先に実行しておかないと途中でハングしたようになるようだ。 writeb ... writef ... でFLASHに書き込んでいくようだが、手作業ではやってられないので書き込みツールをプログラムしてみた。(ツールのソースは下の方) WHR-G54のファームwhrg54-216.binをこのツールで書き込んでみる。1ブロック(64KB)を94秒ほどかけて書き込むようだ。DD-WRTのファームが3692KBなので58ブロック分上書きしてみた。再起動するがチェックサムが違うらしい。ツールで書き込む前に手作業で0xffc00000付近で書き込みしていたためのようだ。WHR-G54のファームと実際に書き込まれているファームのバイナリを比較したら違っていた。58ブロックから0xffc00000の64ブロックまで追加で書き込んだ。 ---- &spanclass(fillbox){結果} 復旧作業の結果、WHR-G54として動作している。FLASHの構造などを記しておく。 #divclass(bordershow){ |0xff800000-0xffefffff&br()7MB|ファームウェア|/dev/fl1| |0xfff00000-0xfff6ffff&br()448KB|ブートコード|/dev/fl2| |0xfff70000-0xfff7ffff&br()64KB|?|?| |0xfff80000-0xffffffff&br()512KB|設定ファイル|/dev/fl0| } ----

BLR3-TX4@failDD-WRT

2008-08-18T23:12:56+09:00

*DD-WRT失敗 &spanclass(fillbox){準備} WHR-G54化した[[BLR3-TX4]]にDD-WRTを入れてみることにする。入れるファームは dd-wrt.v24_vpn_whr-g125.bin である。なぜこれを選んだのか...?!　覚えていない。どこかでWHR-G125≒WHR-G54の情報を見たのだろう。 ---- &spanclass(fillbox){ファーム書き換え} シリアル経由でログインし、nfs上のファームを書き込む。リブート。・BHR-G54化したBLR3-TX4 　ファームは2.16 　LAN側IP 192.168.1.xxx ・nfsサーバ　IP 192.168.1.yyy 　ファームがある位置 /pub mount -t nfs 192.168.1.yyy:/pub /mnt cat /mnt/dd-wrt.v24_vpn_whr-g125.bin > /dev/fl1 reboot ．．．失敗。「ALERT MODE」とやらが起動している。どうやら違うものをいれたらみたいだ。 ---- &spanclass(fillbox){追記} DD-WRTを入れたとき「ALERT MODE」のログをとっていなかった。動作中のファームの先頭を壊して「ALERT MODE」が出るようにしてみた。 echo "ABC">/dev/fl1 reboot 「ALERT MODE」 No PLD model ******* Product Information ******* ---------------------------------- Product Name: WHR-G54 VER: 2.16 Date: 2005/5/12 14:16:3 ---------------------------------- Firmware check:Fail!:checksum error 61626309 [Alart mode] #help commands: ledstop flash erasek writeb writef mmb md help quit >RET:0 #ledstop >RET:0 #md ff800000 FF800000 : 6162630A 00000202 5748522D 47353400 FF800010 : 00000000 00000000 00000000 00000000 FF800020 : 00000000 00000000 312E3031 00000000 FF800030 : 00000000 00000000 00000000 00000000 FF800040 : 00000000 00000000 00020010 00006905 FF800050 : 0C0E1003 0065509B 3BD363D4 0000006C FF800060 : 000B2959 000B29C5 005A26D6 1F8B0808 FF800070 : 8AE68242 0203766D 6C696E75 7800E45C >RET:0 # ----

BLR3-TX4@toWHR-G54

2008-08-18T18:01:07+09:00

*WHR-G54化 &spanclass(fillbox){なんで．．.} DD-WRT化していろいろやっていた[[WLA-G54]]だが、openvpn設定中にflashの内容を壊してしまった。今はただの４ポートスイッチハブになっている。無線LANのAPが欲しかったためWLA-G54搭載の無線LANカードを[[BLR3-TX4]]に積んでAPにしようとしたことから始まる。 DD-WRT化してWLA-G54と同様の環境を作りたかったのだが、BLR3-TX4にDD-WRTを入れたという情報がなかった。BLR3-TX4を無線化(WHR-G54化)したという情報があったためまずはやってみる。参照先 &html(http://www.yamasita.jp/blr3-tx4/index.html#hacknokiroku) 感謝! ---- &spanclass(fillbox){ファーム書き換え} シリアル経由でログインし、nfs上のファームを書き込む。リブート。・BLR3-TX4 　ファームは1.45 　LAN側IP 192.168.1.xxx ・nfsサーバ　IP 192.168.1.yyy 　ファームがある位置 /pub mount -t nfs 192.168.1.yyy:/pub /mnt cat /mnt/whrg54-216.bin > /dev/fl1 reboot ---- &spanclass(fillbox){WHR-G54化後の起動ログ} No PLD model ******* Product Information ******* ---------------------------------- Product Name: WHR-G54 VER: 2.16 Date: 2005/5/12 14:16:3 ---------------------------------- Firmware check:Done. 以下、略。 ----

BLR3-TX4@SCI

2008-08-18T17:55:57+09:00

*シリアル接続 &spanclass(fillbox){ピンヘッダ追加} LED側にJ1のスルーホールがあるのでヘッダピンを追加する #divclass(bordershow){ |J1|1pin|TXD| |~|2pin|RXD| |~|3pin|+3.3V| |~|4pin|GND| } //#image(sci-1.jpg) ---- &spanclass(fillbox){レベルコンバータの用意} [[BLR-TX4シリアル接続>BLR-TX4@SCI]]で使用したものと同じ ---- &spanclass(fillbox){BLR3-TX4起動ログ} No PLD model ******* Product Information ******* ---------------------------------- Product Name: [[BLR3-TX4]] VER: 1.45 Date: 2005/5/12 14:42:53 ---------------------------------- Firmware check:Done. >> Now Loading...done. Now Booting hwid(0) : CLK_DCR value(0x3878) --> unknown hwtype value(0x3878) Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb HWTYPE:None PLD Model Linux version 2.4.18_mvl30-sandpoint (root@scbmrh.localdomain) (gcc version 2.95.3 20010315 (release/MontaVista)) #188 ﾌﾚ 5ｷ 12 14:42:22 珵ST 2005 PCI Autoconfig: Found Bus 0, Device 11, Function 0 PCI Autoconfig: BAR 0x10, I/O, size=0x100, address=0xbfff00 PCI Autoconfig: BAR 0x14, Mem size=0x400, address=0xbffffc00 PCI Autoconfig: Found Bus 0, Device 12, Function 0 PCI Autoconfig: BAR 0x10, I/O, size=0x100, address=0xbffe00 PCI Autoconfig: BAR 0x14, Mem size=0x400, address=0xbffff800 PCI Autoconfig: Found Bus 0, Device 14, Function 0 PCI Autoconfig: BAR 0x10, Mem size=0x2000, address=0xbfffc000 AirStation Pro Series 802.11b Wireless Access Point 2002 MELCO INC. (c) On node 0 totalpages: 16384 zone(0): 16384 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: OpenPIC Version 1.2 (1 CPUs and 26 IRQ sources) at 80040000 Calibrating delay loop... 130.66 BogoMIPS Memory: 57260k available (1244k kernel code, 488k data, 184k init, 0k highmem) Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes) Inode-cache hash table entries: 4096 (order: 3, 32768 bytes) Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 16384 (order: 4, 65536 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Disabling the Out Of Memory Killer pty: 256 Unix98 ptys configured MELCO WLM-L11G RTC DRIVER ver 1.00 MELCO WLM-L11G INIT SWICH DRIVER ver 1.01 initsw: Done. Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x80004600 (irq = 22) is a ST16650 ttyS01 at 0x80004500 (irq = 21) is a ST16650 Software Watchdog Timer: 0.05, timer margin: 100 msec block: 128 slots per queue, batch=32 RAMDISK driver initialized: 16 RAM disks of 20480K size 1024 blocksize loop: loaded (max 8 devices) FLASHDISK:Boot From OnBoard Flash Can't find MiniPCI Board Initialized [TOSHIBA VT641FT] Find Onbord Flash dev_winbond 0 Linux Tulip driver version 1.1.1-NAPI (Feb 16, 2002) brg0: ADMtek Comet rev 17 at 0xbfff00, 00:07:40:**:**:**, IRQ 16. tulip1: MII transceiver #1 config 3100 status 7849 advertising 05e1. eth1: ADMtek Comet rev 17 at 0xbffe00, 00:07:40:**:**:**, IRQ 17. PPP generic driver version 2.4.1 Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 4096) ip_conntrack (512 buckets, 4096 max) * VPN Masqurade -- IPsec Support reg isakmp:done reg ESP protocol: reg ESP conntrack:done PPTP netfilter connection tracking: registered ip_nat_ipsec : isakmp : done. ip_nat_ipsec : esp : done. PPTP netfilter NAT helper: registered ip_tables: (C) 2000-2002 Netfilter core team NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 ds: no socket drivers loaded! RAMDISK: Compressed image found at block 0 Freeing initrd memory: 5267k freed VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 184k init 4k openfirmware modprobe: modprobe: Can't open dependencies file /lib/modules/2.4.18_mvl30-sandpoint/modules.dep (No such file or directory) INIT: version 2.78 booting Activating swap... Checking all file systems... Parallelizing fsck version 1.19 (13-Jul-2000) Setting kernel variables. Init SW watching daemon starting: done Mounting local filesystems... mount: none already mounted or /dev/pts busy mount: according to mtab, devpts is already mounted on /dev/pts Cleaning: /tmp /var/lock /var/run. dmesg: not found 14:42:53: not found Previous Configuration longing: /bin/tar: Removing leading `/' from member names /bin/tar: etc/ap_servd.conf: time stamp 2002-09-03 11:25:05 is 1031052300 s in the future /bin/tar: etc/apache/.htpasswd: time stamp 1970-01-01 00:09:49 is 584 s in the future /bin/tar: etc/bridge.conf: time stamp 2002-10-19 08:54:31 is 1035017666 s in the future /bin/tar: etc/crontab: time stamp 1970-01-01 00:09:25 is 560 s in the future /bin/tar: etc/hostname: time stamp 1970-01-01 00:00:08 is 3 s in the future /bin/tar: etc/lnkitg.conf: time stamp 2001-12-18 12:47:31 is 1008679646 s in the future /bin/tar: etc/passwd: time stamp 2002-09-09 08:52:22 is 1031561537 s in the future /bin/tar: etc/passwd.nocrypto: time stamp 1970-01-01 00:09:49 is 584 s in the future /bin/tar: etc/phymii.conf: time stamp 1970-01-01 00:09:25 is 560 s in the future /bin/tar: etc/resolv.conf: time stamp 1970-01-01 00:09:31 is 566 s in the future /bin/tar: etc/tmp/resolv.conf.manual: time stamp 1970-01-01 00:09:31 is 566 s in the future /bin/tar: etc/syslog.conf: time stamp 1970-01-01 00:00:06 is 1 s in the future /bin/tar: etc/zebra/ripd.conf: time stamp 2002-08-14 03:20:07 is 1029295202 s in the future /bin/tar: etc/zebra/zebra.conf: time stamp 2002-08-14 01:26:51 is 1029288406 s in the future /bin/tar: etc/zebra/daemons: time stamp 2001-11-27 05:52:22 is 1006840337 s in the future /bin/tar: etc/tmp/resolv.conf.manual: time stamp 1970-01-01 00:09:31 is 566 s in the future /bin/tar: etc/network/interfaces: time stamp 1970-01-01 00:00:06 is 1 s in the future /bin/tar: etc/network/ipchains: time stamp 2001-12-14 03:17:48 is 1008299863 s in the future /bin/tar: etc/hosts: time stamp 1970-01-01 00:09:29 is 564 s in the future /bin/tar: etc/ppp/ip-down.d/dnrd: time stamp 2002-10-28 00:29:50 is 1035764985 s in the future /bin/tar: etc/ppp/ip-up.d/0dnrd: time stamp 2001-05-23 22:12:55 is 990655970 s in the future /bin/tar: etc/ppp/ip-up.d/exim: time stamp 2001-05-23 22:15:58 is 990656153 s in the future /bin/tar: etc/ppp/chap-secrets: time stamp 2002-04-08 01:28:14 is 1018229289 s in the future /bin/tar: etc/ppp/options: time stamp 2002-04-17 13:13:15 is 1019049190 s in the future /bin/tar: etc/ppp/pap-secrets: time stamp 2002-04-08 01:28:02 is 1018229277 s in the future /bin/tar: etc/ppp/pppoe01.conf: time stamp 1970-01-01 00:00:06 is 1 s in the future /bin/tar: etc/ppp/ip-up: time stamp 2002-06-28 01:50:08 is 1025229003 s in the future /bin/tar: etc/ppp/ip-down: time stamp 2002-06-28 01:50:19 is 1025229014 s in the future /bin/tar: etc/ppp/connect-script: time stamp 2002-08-26 04:48:18 is 1030337293 s in the future /bin/tar: etc/ppp/pppoe02.conf: time stamp 1970-01-01 00:09:31 is 566 s in the future /bin/tar: etc/ppp/pppoe01.conf.bak: time stamp 2002-09-27 06:14:11 is 1033107246 s in the future /bin/tar: etc/ppp/pppoe03.conf: time stamp 1970-01-01 00:09:31 is 566 s in the future /bin/tar: etc/ppp/pppoe04.conf: time stamp 1970-01-01 00:09:31 is 566 s in the future /bin/tar: etc/ppp/pppoe05.conf: time stamp 1970-01-01 00:09:31 is 566 s in the future /bin/tar: etc/dhcpd.conf: time stamp 2002-04-12 06:40:27 is 1018593622 s in the future /bin/tar: etc/dhcpd.sw: time stamp 1970-01-01 00:09:31 is 566 s in the future /bin/tar: etc/network/check-mac-address.sh: time stamp 2001-05-23 22:34:48 is 990657283 s in the future /bin/tar: etc/network/get-mac-address.sh: time stamp 2001-05-23 22:34:48 is 990657283 s in the future /bin/tar: etc/network/interfaces: time stamp 1970-01-01 00:00:06 is 1 s in the future /bin/tar: etc/network/pcmcia-compat.sh: time stamp 2001-05-23 22:34:48 is 990657283 s in the future /bin/tar: etc/network/ping-places.sh: time stamp 2001-05-23 22:34:48 is 990657283 s in the future /bin/tar: etc/network/options: time stamp 2002-02-05 06:51:09 is 1012891864 s in the future /bin/tar: etc/network/ifstate: time stamp 2001-12-14 00:51:44 is 1008291099 s in the future /bin/tar: etc/network/ipchains: time stamp 2001-12-14 03:17:48 is 1008299863 s in the future /bin/tar: etc/network/easyfilter: time stamp 2002-04-19 00:57:51 is 1019177866 s in the future /bin/tar: etc/network/easyfilter_init: time stamp 2002-04-19 00:58:00 is 1019177875 s in the future /bin/tar: etc/network/nattables: time stamp 2002-04-05 08:25:12 is 1017995107 s in the future /bin/tar: etc/network/iptables.sw: time stamp 2002-04-12 04:42:18 is 1018586533 s in the future /bin/tar: etc/network/packetfilter: time stamp 2002-04-13 06:05:29 is 1018677924 s in the future /bin/tar: etc/network/dn_filter: time stamp 2002-08-29 01:18:18 is 1030583893 s in the future /bin/tar: etc/network/attackblock.conf: time stamp 2003-03-24 09:14:48 is 1048497283 s in the future /bin/tar: etc/network/macaddress.conf: time stamp 1970-01-01 00:09:27 is 562 s in the future /bin/tar: etc/upnpd.conf: time stamp 1970-01-01 00:09:49 is 584 s in the future /bin/tar: etc/ver_up.conf: time stamp 1970-01-01 00:00:06 is 1 s in the future /bin/tar: tmp/save_kernel_version: time stamp 1970-01-01 00:00:07 is 2 s in the future done rm: cannot remove `/etc/ppp/ip-down.d/00delresolv': No such file or directory ver_up: Ver 145 to 145: no change. set phy to wired lan device: done set phy to wired wan device: done Configuration network interface: netifctl[72]: Boot up network device netifctl[72]: lo starts to up netifctl[72]: brg0 starts to up **** /sbin/dhcpcd: not running Stopping Zebra daemons: (bgpd) (ripd) (ripngd) (ospfd) (ospf6d) (zebra). Starting Zebra daemons (prio:10): zebra ripd. netifctl[72]: eth1 starts to up **** /sbin/dhcpcd: not running Stopping Zebra daemons: (bgpd) ripd (ripngd) (ospfd) (ospf6d) zebra. Starting Zebra daemons (prio:10): zebra ripd. SIOCADDRT: File exists netifctl[72]: Success done. Hostname: AP000740******. Initializing random number generator... done. Checking password and group files... grpck: not found Starting system log daemon: syslogd syslogd: /var/log/attack_pipe: No such file or directory klogd. Setting Networking rules.. INIT: Entering runlevel: 2 -ne Starting web server: apache . Starting AP serv daemon:AP serv starting on brg0 Starting periodic command scheduler: cron/var/spool/cron: No such file or directory /var/spool/cron: created crontabs: No such file or directory crontabs: created . Starting internet superserver: inetd. [IPTABLES START] +Packet Filter +Enabled +Easy Filter +Disable NBT Routing +Reject IDENT Packet +Allow ICMP Echo reply +IP MASQUAREDE +Enabled +UPnP Settings [DONE] Starting Zebra daemons (prio:10): (zebra) (ripd). default: not found ppp0: not found ppp1: not found ppp2: not found ppp3: not found ppp4: not found Start DNS Relay Daemon Notice: caching turned off $Starting fwlogwatch: MELCO Daemon reboot Deamon 'NINJYA' 0: dnsrd /var/run/dnrd.pid /etc/init.d/dns-relay start 1: apservd /var/run/apservd-brg0.pid /etc/init.d/apservd start 2: wcc /var/run/wcc.pid /etc/init.d/wcc restart MELCO INC. AirStationPro Series BLR3-TX4 Ver 1.45 AP000740****** login: ----

WLA-G54

2008-08-18T17:00:20+09:00

*WLA-G54 &spanclass(fillbox){ハードウェア構成} #divclass(bordershow){ |ボード型番|WL4BMS4-DA|| | |CPU|BCM4702KPB|125MHz|| |SDRAM|VG36641641DT-7L&br()×2|16MByte|| |Flash ROM|M29W3200T 70N6|4MByte|70ns| |WAN|||| |LAN|||| |switch device&br()(LAN側)|BCM5325A2KQM||5portスイッチチップ&br()Port-based VLAN(br()802.1p QoS priority| |miniPCI||1slot|| } ---- ---- ----

BLR3-TX4

2008-08-18T15:54:22+09:00

*BLR3-TX4 &spanclass(fillbox){ハードウェア構成} #divclass(bordershow){ |ボード型番|WLNMML4-CA|| | |CPU|XPC8241LZP200B|200MHz|| |SDRAM|VG36128161BT-7L&br()×4|64MByte|| |Flash ROM|TC58FVM6T2ATG65|8MByte|| |WAN|AN983B|10/100Mbps|with PHY| |LAN|AN983B|10/100Mbps|with PHY| |switch device&br()(LAN側)|BCM5325A2KQM||5portスイッチチップ&br()Port-based VLAN&br()802.1p QoS priority| |miniPCI||1slot|| } ---- ---- ----

WLAR-L11@SCI

2008-07-18T23:09:39+09:00

*シリアル接続 &spanclass(fillbox){ピンヘッダ追加} SH3のSCIはJ1までパターンがつながっているので利用する。 #divclass(bordershow){ |J1|1pin|TXD|SH3-TXD0(164pin)| |~|2pin|RXD|SH3-RXD0(171pin)| |~|3pin|+3.3V|| |~|4pin|GND|| } //#image(sci-1.jpg) ---- &spanclass(fillbox){レベルコンバータの用意} [[BLR-TX4シリアル接続>BLR-TX4@SCI]]で使用したものと同じ ---- &spanclass(fillbox){WLAR-L11起動ログ} ac000000 -- ac3fec3c : start 4byte mem check Now filling...ac000000 -- ac3fec3f (adrs) ac000000 ac100000 ac200000 ac300000 checking.. ac000000 ac100000 ac200000 ac300000 mem check complete ac000000 -- ac3fec3c : FILL 0 data ------------- debug_ident=0 rst_type=0 expevt=0 intevt=0 intevt2=0 spc=0 ssr=0 reset_status=0 144458 P_CLK= 20 MHz DBserial=57600 serial=115200 WLA_CLK_MODEHI= 1 ** Free Program Area=206238 RAM_DEBUG_POINTER=c3fec00 -- WLA_FLASH_BASE -- firmsize=784996 chksum=bef5c2c0 fwcode=6 author=HIRAI HABA OHARA TAMURA YAMAZAKI SUGAI date=Fri Oct 05 17:00:05 2001 sig=[[WLAR-L11]] ver=220 fwcode=6 WLA_TYPE=4 WLA_AREA_=0 HW model=00000036 RunTime CPU CHECK (CPU=SH7709) all_initialize end ------ Application_Initialize (freemem=3488572)------ 144458: ***** System_startup_task ***** Init_SCI_Driver(): Create Driver sci end Init_SCI_Driver end FUJITSU MBM29LV800T FUJITSU MBM29LV800T HW model=00000036 144458: Network Initialize start 144458: WLA setup data loading.. 0000: 00 40 26 ** ** ** 00 00-00 00 00 00 00 00 00 00 .@&............. AX88195 MAC 00:40:26:**:**:** WEB data size=5664 WEB data size=6622 144458: mode is WLA_MODE_BRIDGE ** NetDriver [WLARL11] Ver.1.00 (Oct 05 2001-16:56:26) -> WLARL11_Init ** NetDriver [AX88195] Ver.1.00 (Oct 05 2001-16:56:23) -> AX88195_Open_Device in == start AX88195 InternalRAM check == <- AX88195_Open_Device end ** ram_memcpy param err s=c15ac78 d=c15ac78 6 MAC ADR= 00 40 26 ** ** ** <- AX88195_Init ** NetDriver [LUCENT] Ver.1.00 (Oct 05 2001-16:56:21) TPL code=1 size=3 TPL code=17 size=4 TPL code=1d size=5 x 1o[W version=5 0 MELCO WLI-PCM-L11 Version 01.01 ---- wvlan2_private ---- PortType =1 Channel =0 TxRateControl =3 APDensity =1 RTSThreshold =2347 PMEnabled =0 MulticastReceive =1 MaxSleepDuration =100 MACAddress =00:00:00:00:00:00 NetworkName =AirStation StationName =AIRCONNECT EnableEncryption =0 WEPOption =0 Key1 = Key2 = Key3 = Key4 = TransmitKeyID =1 ---- IFB ---- IFB_Version =5 IFB_IOBase =ba000300 IFB_IO_Range =40 IFB_Magic =7d37 IFB_HCF_VersionMajor =2 IFB_HCFVersionMinor =22 IFB_TickIni =262144 IFB_CfgTblSize =352 ---- driver Info ---- len =13 typ =2085 driver_name =WVLAN49 driver_version =400 HCF_version =222 IO_address =300 IO_range =128 IRQ_number =49 card_stat =0 frame_type =1 ---- driver Info ---- len =5 typ =2086 comp_id =49 variant =1 version_major =4 version_minor =0 WaveLAN AP Firmware download:Done. Port Type fail. RTS Threshold fail. Tx Rate Control fail. Power Management fail. CFG_CNF_MCAST_RX fail. CFG_CNF_MAX_SLEEP_DURATION fail. WVLAN49: WaveLAN/IEEE,io_addr 0xba000300,irq_vect 49, mac_address 00:00:00:00:00:00 <- LUCENT_Init <- WLARL11_Init ** Rip2 Bootup ****************** Call IpConfig Func *** IPCONFIG_OPERATE(3),Interface(Local),IP(0),Mask(0) GetMAC iface=0 NERR_FATAL/rip2.c/NU_Rip_Initialize 6 IP is 192.168.1.3 -- RATE=2 Port Type fail. RTS Threshold fail. Tx Rate Control fail. Power Management fail. CFG_CNF_MCAST_RX fail. CFG_CNF_MAX_SLEEP_DURATION fail. Port Type fail. RTS Threshold fail. Tx Rate Control fail. Power Management fail. CFG_CNF_MCAST_RX fail. CFG_CNF_MAX_SLEEP_DURATION fail. -- ESSID=8291BADEVELOP Port Type fail. RTS Threshold fail. Tx Rate Control fail. Power Management fail. CFG_CNF_MCAST_RX fail. CFG_CNF_MAX_SLEEP_DURATION fail. -- CHANNEL=11 Port Type fail. RTS Threshold fail. Tx Rate Control fail. Power Management fail. CFG_CNF_MCAST_RX fail. CFG_CNF_MAX_SLEEP_DURATION fail. -- WEP Disable Port Type fail. RTS Threshold fail. Tx Rate Control fail. Power Management fail. CFG_CNF_MCAST_RX fail. CFG_CNF_MAX_SLEEP_DURATION fail. ** LUCENT WEP Option Disable ---- IFB ---- IFB_Version =5 IFB_IOBase =ba000300 IFB_IO_Range =40 IFB_Magic =7d37 IFB_HCF_VersionMajor =2 IFB_HCFVersionMinor =22 IFB_TickIni =262144 IFB_CfgTblSize =352 Port Type fail. RTS Threshold fail. Tx Rate Control fail. Power Management fail. CFG_CNF_MCAST_RX fail. CFG_CNF_MAX_SLEEP_DURATION fail. -- MAC Filter Disable **** SetPacketFilter ************* SetRIP Call IpConfig Func *** IPCONFIG_OPERATE(3),Interface(Local),IP(0),Mask(0) GetMAC iface=0 ** Rip2 Interface(WLAR-L11) seting ! sendmode = 0 recvmode = 3 NERR_FATAL/rip2.c/NU_Rip2_Change_Command 1 GetMAC iface=3 ----

WLAR-L11

2008-07-18T22:45:46+09:00

*WLAR-L11 &spanclass(fillbox){ハードウェア構成} #divclass(bordershow){ |ボード型番|WLAN-DA|| | |CPU|SH3 7709 F80B|80MHz|CLK≦80MHz&br()IO 3.3V&br()internal 1.8V| |SDRAM|VG3617161DT-8&br()×2|4MByte|8ns 125MHz@CL3&br()524,288word×16bit×2-bank&br()4096refresh cycles/64ms| |Flash ROM|29LV800TA-90PFTN|1MByte|90ns&br()8Mbit(1M×8bit or 512K×16bit)&br()Top sector| |WAN|AX88195|10/100Mbps|| |LAN|||| |PHY(WAN側)|KS8737||| |PCMCIA||1slot|| } ---- &spanclass(fillbox){エリアマップ} #divclass(bordershow){ |CENTER:エリア|CENTER:アドレス|CENTER:バス幅|CENTER:| |エリア0|&tt(){0x00000000 - 0x03FFFFFF}|CENTER:16|FLASH ROM| |エリア1|&tt(){0x04000000 - 0x07FFFFFF}|CENTER:|| |エリア2|&tt(){0x08000000 - 0x0BFFFFFF}|CENTER:|| |エリア3|&tt(){0x0C000000 - 0x0FFFFFFF}|CENTER:32|SDRAM| |エリア4|&tt(){0x10000000 - 0x13FFFFFF}|CENTER:|| |エリア5|&tt(){0x14000000 - 0x17FFFFFF}|CENTER:16|AX88195| |エリア6|&tt(){0x18000000 - 0x1BFFFFFF}|CENTER:16|| } ---- ----